Search

Search all blog posts here.

Search This Blog

Tuesday, May 3, 2016

Broken LeatherLyke Bag Fix - 1500 Vulcan Classic

So my LeatherLyke bags broke again. I fixed this back in 2003, so that was a pretty good fix. There was a bit of sheetmetal, some fiberglass mat, bondo, and spray paint. The weird thing is that the right bag has broken twice for no apparent reason at all, but I have actually slid the whole bike on top of the left one and it's fine. Anywho, this isn't an original idea for a fix, but I figured I would show my take on it for what it's worth.


Drill out the rivet that holds the strap that holds the hair pin clips. One end of that strap is already broken anyway.


One of the bigger things I wanted to show compared to MarkT's write-up is that I bought some clecos to make the alignment and fit easier and nicer. I'm also going to use 1/8 inch rivets.


Another note of difference between the Valkyrie LL bags is that the Vulcan has another fender strut bolt right here.


A little brown bag template action.


I hogged out the basic shape from 22 gauge steel. I drilled one hole through the metal and bag and set a cleco. I then drilled a second hole through both and set a cleco. That's when Scott "Hotsauce" really got to work for me.



He marked the shape better and started to shape it up.


I must say if you're going to do any sheet metal work then you need the three piece Wiss snips for sure, not cheap ones.


He's been watching a lot of Full Custom Garage, so now he really knows how to build stuff.


Once the outer piece was shaped up where we liked it, another hole and cleco was placed near the damaged area.


An inner piece was shaped to fit and transfer drilled for the clecos and eventually rivets. The large hole location was marked as well. This piece was only a few inches long. The fender bolt clearance spot limited the length, but it should be enough.


Centerdrill the inner piece.


Now cleco the outer to the inner and transfer drill the center hole of the large hole to the outer piece.


We used the biggest bit we had on hand to drill the large hole. It was not big enough of course, but we can fix that too.


Carefully dremel out the large hole to match the bag.


Repeat those steps for the inner piece.


Take apart, rework, again, and again until the grommet fits.


And make sure the holder and bolt fit, too.


Lay out the rest of the rivets.


I had to adjust the pitch and offset a bit because of the fender bolt clearance spot. I was thinking that I would omit that bolt and not need a hole in the sheetmetal to clear it.


I drilled and dremeled the front hole to size.


A little black paint to keep the rust away.


Oops, I thought I could omit this bolt, but it does help with the sissy bar.


The trick is locating it correctly. I put the clecos, grommets, and holders in place.


Then I removed the clecos. I figure the grommets had things close enough.


Luckily I had a spare (blacked-out) fender strut on hand.


I put the bolts through the bag and fender strut then transfer punched the center location of the last hole.


This hole doesn't need to be as large as the mounting holes it just needs to clear the head of the bolt.


Finally getting down to the rivets. I figured I wanted to use some black silicon to seal around the rivets.


The high temp isn't needed, but the black will blend in.


Fit one cleco.


Pack the broken area with silicon.





Place several clecos and start with the rivets.





For the rivets without the inner piece I used the rivet washers to avoid pulling through the plastic.


Looking great. I will let the silicon set up over night though.


Two standard 5/16 washers are perfect for pushing the holders out just enough to clear the rivet heads.


Paracord, it's the new duct tape or something like that. I made a new lanyard for the hair pin clips.


I routed the lanyard like this so that I wouldn't pull the pins accidentally while loading the bags.


Good to go. Hopefully I can get about 70,000 miles out of this fix, too.


Note Taking for Group Riding


I have a friend, Pibb, that takes notes and journals every day and every ride. The Every Day Carry (EDC) Community is huge on carrying small notebooks and I have taken to carrying a Field Notes book with a cover that Joker made for me.  I generally only write down reminders, to do lists and addresses, but it is very handy to have. All of this to make a point on how good notes taking can improve group rides and long rides. 

Smartphones and GPS are great, but very prone to getting broke or going dead.   Here is what I am thinking. Carry a riding notebook, especially on a cross country group trip. The first thing you need to write down in your notebook is your emergency contact. That will be huge if(God forbid) you get hurt. The next thing you need is your addresses and phone numbers of any stops or rally spots. I always write a plan for the route that I can see while I ride(example, example), but having more notes and numbers is always good. The next thing that could be very helpful is getting the phone number and emergency contact of everyone that’s riding with you. Having everyone’s number is great if you lose somebody on the ride. Also I have a ton of riding buddies from the internet that I don’t even know their full legal name or even who to call if(God forbid) they get hurt on a ride. It’s also really cool to have phone numbers to call all your best friends from the internet later.

I plan on carrying a Rite in the Rain mini side stapled notebook and Trekker Space Pen for all my long rides and day trips in the coming up. The Rite in the Rain should hold up better to sweat and rain, than a regular Field Notes stapled notebook.

Wednesday, April 6, 2016

The correct 4 speed drain plug seal

There is a correct 4 speed drain plug seal. Shout out to JB in NC for the hook-up. 62702-52

Wednesday, March 30, 2016

Finally Got Big Boy on his Bike

It was a long time coming.



Lummie's New Springer

So my buddy Lummie moved to South Dakota and left me a bunch a parts he didn't want and just some fond memories. Then he calls me up to go look at a bike locally and see what I think and get pictures. If he decides to buy, then I get to ride it for him until he can come pick it up. So here it is.



Aftermarket 5 speed kicker kit. Groovy mid peg set-up, but I know I could talk Lummie out of the pegs.


Gold plated springer bits.







Check out the coils and connections for the ignition.






Nearly new rear tire.


Some rust on the hubs.



Here's the ignition brain box. MDS Pulse, high dollar and programmable (I don't see the point on a stock 80 inch Evo)


Overall, not a bad sled.



Yes, started raining on me forty miles from home.













So Lummie decides he wants it. So I have my wife drive me like 40 miles one way to go get it. Then I drive it home with just one hiccup, but otherwise it drove and ran great. I get home and I start playing with the kick starter a bit and I'm having mixed results, but mostly success. That's when I decide to e-start it and run it for a bit to make sure I hadn't flooded it or anything.  The e-start barely makes a click. I can't figure how messing with the kick had affected the e-starter. Well, it hadn't.  I checked the battery and the voltage was like 9V.  I was really lucky to have made it home on this bike. Battery(supposed to be new), stator, or regulator? Park it with the trickle charger on it for now.



Oh and then there's this. Everyone keeps telling me that EVO's and 5 speed don't leak.



Lummie showed up like two weeks later, before I could fix it and ride it. Luckily the stator was still putting out good AC, so it only needed a regulator. Lummie brought a Dyna-S to put in it as well.


Put up level on the jack and leak was clearly an overfilled primary. Oil went everywhere when we popped off the derby cover. As Pat says, "Another expert Harley mechanic. The internet is full of them."



Time to swap the regulator and ignition.


Yep, we had to pull a tank to find the VOES switch connected to the brain box.


I had to leave for a bit, so I didn't get all the repair action, but here's how it finished up. New regulator and no ignition box out front.



Here it is ready to go to South Dakota. I was really bummed that I only got to ride once.


Tuesday, March 29, 2016

4 Speed Stud - Keyed Insert fix

I wouldn't call this fix a fail, but it was probably more time, energy, and money than really needed to be spent. I learned a few things and that's why I blog and share.

This stud is loose and I actually thought it was the source of my leak.


See it wiggle.

I decided to try key locking threaded inserts(keenserts) instead of my usually helical threaded insert (heli-coils). The goal was thinking that a keensert would be easier to seal than a heli-coil. I was also under the impression that keenserts have an OD thread in a standard pitch and can be installed with just a standard bolt. So no special tap or install tool would be needed. Both are true to a degree, but as I found, not completely accurate in this specific case.

I had some trouble finding a small batch of inserts in the size I wanted, but I did find 3/8-16 ID and 9/16-12 OD on ebay.


I had searched for the thin wall version with a 1/2-13 OD, but 9/16-12 is the best I could do on a budget. So I had to check to make sure I had enough case left for the oversized hole. That looked okay.


I need a work stand for my transmission and couldn't find the box I built last time. So I figured out a new way. Luckily, I already had some 3/4 inch plywood ripped to 4 1/8 inch wide and this was a perfect start.


Here are the rough locations of the bottom studs. This was kind of a hack job, but with the holes oversized it fit just fine.


I screwed two of the narrow boards together and then screwed that to a larger board for support.


It was pretty good, but still a bit cantilevered out so I slipped a scrap of plywood under the kicker end and I really liked the set-up.


Thinking this was a through hole, I began to step up the drill sizes and pack the bit with grease so that the chips wouldn't go into the transmission.


See how that holds the chips.


Well I figured out that the hole wasn't through and not the source of my leak, but I had to carry on at this point.


Did I say I wouldn't need a special tap? Well I didn't, but I still had to buy a tap because I didn't have a 9/16-12 and most stores don't carry anything over 1/2. So the no special tap really didn't have any advantage in this situation.


On to the no special install tool part, yes there are special tools but you can get by without them. The OD pitch is a very tight interference fit and using an allen bolt to install it was very tough. The dang thing wanted to cross thread extremely bad. Next time I will drill the hole slightly larger than normal spec for the given thread pitch. I wasted a couple trying to get them in.


Success. I got one in. It was so tight that I don't think the stakes were ever needed.


The hole is good now.


No wiggle and set with loctite.

Tuesday, March 1, 2016

39 vs 40 tooth engine belt sprocket

So my primary belt is too tight and the transmission adjusted all the way forward, so I decided that a 39 tooth front pulley would be the way to get everything to fit.

For what it's worth I was running a 62-40 SK3 kit with the BDL-30853 BE "Bullseye" Belt. BDL number convention breaks that out as 62 tooth clutch basket, 40 tooth engine sprocket, S for splined engine sprocket, K for kick only(no e starter ring.), and I have no idea what the 3 means. BDL lists this as a kit for 1965-1978.  It's too tight on my rigid frame of unknown origin.

Swapping the engine sprocket to 39 tooth will give me the same set-up as a 62-39 SK2 kit which BLD lists as fitting a 1955-1964. As it turns out this is the kit I should have started with.

First let's look the actual diametrical differences between the 39 and 40 tooth pulley. The 39 is smaller of course.


With just a very basic reference measurement the 40 tooth is 3.985 inches across.


Using the same methodology the 39 tooth is 3.890 inches. So about 0.100 inch difference; which doesn't seem like a lot.


Here's the cold belt tension with the 40 tooth sprocket.
Here's the cold belt tension with the 39 tooth sprocket with everything else the same. That's actually a bit on the loose side.
Look at how much slack there is. I'm considering running a standard belt instead of a bulls-eye because it actually fit just about right.


Time to tear down the clutch and swap the transmission 23 tooth sprocket for a 25 to get my gearing back in order. Ugh, more unplanned stuff.  The lower left stud has decent enough thread to hold things together, but the stud has a bunch of lateral play and is leaking. I knew this already and tried to fix it with plumber's tape, but yeah that didn't work. Now I need to fix that. Stay tuned.